Your benefits
A new mower design
Limiting the weight and loads on the tractor components were key criteria when designing the machine. These goals were reached thanks to the new design of the frame and mowing-grouping unit holding arms which allowed reducing the weight, increasing the compactness with a centre of gravity set 15 cm forward with regards to conventional machines. A notable weight reduction also comes from the belt conveyor frames made of aluminium. The reasonable weight is also an advantage at work: lower power requirement and limited soil compaction. Furthermore, the action of the hydro-pneumatic suspension facilitates ground following.
A large width machine easy to manoeuvre
Remarkable stability, particularly for transport. The machine's design limits load transfer on the rear axle, owing to its conveyor structures in aluminium and mowing units located closest to the tractor. The reasonable weight and optimized centre of gravity improve the tractor's balance and stability for safe transport.
A compact machine with easier access
The front guards automatically retract in transport position for easier and secure access to the rear of the tractor! It is possible also to retract them when the machine is unfolded for easy access in order to replace knives or for machine cleaning. The mower can be stored in the vertical position to reduce the space requirement for winter storage.
Quality work with ground following
Benefit from the OPTIDISC ELITE cutter bar
The 2 mowing units are fitted the OPTIDISC ELITE cutter bars with 8 discs and 3.50 m working width. For optimum work on bends or slopes, the cutting overlap with a front mower conditioner FC 3125F is 42 cm per side! Clean forage is the key to success for savings in concentrates to be added into the herd's feed. The varying spacing between discs, the large overlap areas and small mowing angle of the OPTIDISC ELITE cutter bar provide the much sought-after quality.
Where discs diverge, spacing is reduced for increased knife overlap. Clean mowing even in short or light forage.
Where discs converge, spacing is larger, offering more space for forage to flow. It is quickly expelled rearwards, the mower work is not disturbed.
On hilly grounds, in wet or sticky grass conditions, soil can build up in front of the cutter bar, except with the OPTIDISC ELITE! Its specific skids improve gliding and preserve the sward. Another benefit for forage quality especially in difficult conditions.
Where discs diverge, spacing is reduced for increased knife overlap. Clean mowing even in short or light forage.
Where discs converge, spacing is larger, offering more space for forage to flow. It is quickly expelled rearwards, the mower work is not disturbed.
On hilly grounds, in wet or sticky grass conditions, soil can build up in front of the cutter bar, except with the OPTIDISC ELITE! Its specific skids improve gliding and preserve the sward. Another benefit for forage quality especially in difficult conditions.
Maximum reliability and hold
The cutter bar has been designed to cope with obstacles. With the PROTECTADRIVE safety system, in case a disc hits an obstacle very violently, the shaft holding the disc shears above a cleverly dimensioned shearing groove above the bearing. Gearwheels are protected. In less than 15 minutes, the machine is operational again at a very low repair cost.
The bearing is fastened by long screws, going through the cutter bar. Risk of bearings being torn out in case of a shock is prevented.
High-end components reinforce the core of the cutter bar:
- cutter bar with special double row angular contact ball bearings.
- Large diameter gearwheels in high precision forged steel with 3 teeth intermeshing.
- Discs with forged and fully heat treated cups.
- Heat treated steel disc skids with possibility of adding protective lining (fastening per screw).
To increase the machine's service life, dampers are fitted between the cutter bar and the frame. When mowing at high ground speed, the machine structure is less affected by shocks.
The bearing is fastened by long screws, going through the cutter bar. Risk of bearings being torn out in case of a shock is prevented.
High-end components reinforce the core of the cutter bar:
- cutter bar with special double row angular contact ball bearings.
- Large diameter gearwheels in high precision forged steel with 3 teeth intermeshing.
- Discs with forged and fully heat treated cups.
- Heat treated steel disc skids with possibility of adding protective lining (fastening per screw).
To increase the machine's service life, dampers are fitted between the cutter bar and the frame. When mowing at high ground speed, the machine structure is less affected by shocks.
Maintenance reduced to the minimum
Maintenance will not take all your time.
The OPTIDISC ELITE cutter bar is an excellent example of added value created thanks to the close cooperation between manufacturer and farmers. This solution is fully adapted to the practice and helps you save time owing to:
Maintenance is essentially limited to the drive components and a few pivot points, and at large intervals.
The OPTIDISC ELITE cutter bar is an excellent example of added value created thanks to the close cooperation between manufacturer and farmers. This solution is fully adapted to the practice and helps you save time owing to:
- Life-lubrication. Maintenance-free cutter bar.
- The fully safe FAST-FIT knife attachment system comprises a leaf spring ensuring constant pressure on the fastening screw for further safety. Knife replacement requires little time.
Maintenance is essentially limited to the drive components and a few pivot points, and at large intervals.
NON-STOP safety system combined with the LIFT-CONTROL suspension
During the high season, nobody can afford to damage the mower because of a forgotten obstacle, or even a wrong manoeuvre.
When encountering an obstacle, the concerned mower unit shifts rearwards around a pivot point. The mower unit automatically returns to the initial position without stopping
When encountering an obstacle, the concerned mower unit shifts rearwards around a pivot point. The mower unit automatically returns to the initial position without stopping
- The safety remains effective even if the obstacle is struck by the inner discs of the mower unit, since the pivot point of the arm is sufficiently far from the first discs.
- The front edge of the mower unit rises slightly, providing additional clearance.
High-performance and easy-to-adjust conditioning
The new conditioner with metal fingers contributes to the weight reduction of the machine. The lever-controlled two-speed gearbox offers the possibility of operating the conditioner at a slower speed to preserve the most delicate forages. Conditioning is easily adjusted to suit forages and weather conditions. The standard recycling plate (placed between mowing unit and belts), prevents forage loss.
The conveyor belts are driven by 2 pumps supplied by a tank integrated into the central frame. The other hydraulic functions use a hydraulic unit connected in load sensing to the tractor (folding, lifting-lowering on headland, conveyor positioning, suspension). This design avoids significant hydraulic requirements during work, eliminates overheating and increases the responsiveness of machine functions. The tension of the belts is set centrally, quickly and with ease.
The conveyor belts are driven by 2 pumps supplied by a tank integrated into the central frame. The other hydraulic functions use a hydraulic unit connected in load sensing to the tractor (folding, lifting-lowering on headland, conveyor positioning, suspension). This design avoids significant hydraulic requirements during work, eliminates overheating and increases the responsiveness of machine functions. The tension of the belts is set centrally, quickly and with ease.
ISOBUS technology available on a mower
All settings in the cab via ISOBUS
All machine controls are grouped on the tractor ISOBUS terminal or on the CCI 800 or 1200 options available. All machine functions, as well as the front mower, are easily controllable. At a glance, it is possible to view all settings and indicators. Functions such as the integrated headland turn sequence make it easier to operate the mower combination. Contact your KUHN partner to find out more about equipment compatibility.
Even greater comfort of use
Adding an ISOBUS joystick such as the CCI A3 (optional) further improves comfort of use.
Specifications
Technical characteristics
Working width (m) in combination with a front mower |
---|
Overlap between front and rear units (cm) |
Transport width (m) |
Transport height (m) |
Cutter bar |
Number of discs with heat treated protection skids |
Disc skid lining |
Blade attachment |
Cutting height range with standard skids (mm) |
Gear train protection system |
Ground following |
Suspension |
Safety breakaway |
Outer protection |
Conditioning system |
Conditioner speed (min-1) |
Conditioner drive |
Overall swath width (min/max) approx. (m) |
Wide spreading system |
Headland turning position |
Conveyor belt drive |
Forage delivered by conveyor belt |
Operation and function control |
Hitch |
Machine parking |
PTO speed (min-1) |
Overload protection |
Free wheel |
Theoretical tractor power requirement (kW/hp) |
Required tractor hydraulic connections |
Required tractor electrical connections |
Machine control |
Speed signal |
Road lights and signalling on rear |
Approx. weight (kg) |
FC 9330 D-RA | FC 10030 D-FF |
---|---|
9.30 | 9.93 |
42 (FC 3125 DF) / 62 (FC 3525 DF) | 30 - 50 (FC 3525 DF) |
3.00 | 3.35 |
Below 4 m | |
OPTIDISC ELITE cutter bar with FAST-FIT quick release, modular disc bearing stations removable from the outside and fitted with PROTECTADRIVE safety | OPTIDISC ELITE |
2 x 8 (2 x 3.50 m) | 2 x 8 (2 x 3.50 m) |
2 - as standard on each cutter bar | 2 - as standard on each cutter bar |
FAST-FIT quick release | |
35 to 65 | 35 to 65 |
PROTECTADRIVE system | |
Pendulum articulation | Pendulum-type articulation |
LIFT-CONTROL hydro-pneumatic suspension | LIFT-CONTROL hydro-pneumatic suspension |
Non-Stop rearward and upward shifting safety system while at the same time lifting the cutter bar front | Non-stop safety |
Hydraulic folding Flexprotect side guards | |
Pivoting steel fingers - adjustable conditioning plate with 5-position lever | Pivoting steel fingers - adjustable conditioning plate with 5-position lever |
755 or 1000 - adjustable by selector lever | 755 or 1000 adjustable by selector lever |
By gearbox with anti-blocking system | By gearbox with anti-blocking safety |
2 x 1.85 / 2.40 | |
As standard | |
By hydraulic cylinders | |
By integrated hydraulic unit with pumps fitted on the central gearbox. Belt position and speed adjustable from the cab. Possibility to modulate the belt speed according to the slope angle (manual compensation by the driver or automatic by standard built-in inclinometer) | |
To choose from: central delivery (width of 1.80 to 3.60 m), delivery with one side raised (18 m cut delivered over 12 m for raking by a 4-rotor rake), flat delivery | |
Individual lift of rear units and setting into transport position | |
3-point - Cat. 3 or 4N (Quick Hitch cat. 3/4N compatible) | 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) |
Unfolded or folded in vertical position | Unfolded or folded on dedicated parking stands |
1000 | 1000 |
Torque limiter on primary PTO-shaft | Primary PTO-shaft with torque limiter |
Standard - on side gearboxes | Integrated in the side gearbox |
154 / 210 | 162 / 221 |
Rear machine LS connected: 1 x pressure, 1 x free return, 1 x load sensing Front machine: 1 x SA (plus 1 x DA if hydraulically controlled Flexprotect side guards) | 2 DA valves (+ 1 DA optional for the tractor hydraulic top link) |
Rear machine: 1 7-pin plug and 1 ISOBUS plug Front machine: 1 7-pin plug | 1 x 7-pin plug |
ISOBUS machine: use of a CCI terminal or ISOBUS-certified tractor terminal | |
via TECU (if ITH harness, plan a type B cable) | |
As standard | |
3,98 | 3260 |
Media
User Stories:FC 1030 RA
Rob Wrenall Farmer
“It has improved and sped up the process immeasurably. I can control everything using the tractor’s ISOBUS and, whilst the mower is heavy, it is very easy to operate with all the controls, including the merger belts, on one screen''
FOR CONTRACTORS AND LARGE FARMS
In today's world of farming, where fields are getting larger and time is of the essence, having reliable and efficient machinery is crucial. At KUHN, we are here for contractors and big farms like yours.